Edgebanders

The NewCNC Fuse 9 is a heavy-duty Edgebander engineered for continuous duty. This is designed for high production with pre-mill and corner rounding. Typical uses would be commercial cabinets, closets, and work surfaces. The first station is a double motor pre-mill section. Pre-mill finish cuts the edge and leaves the perfect surface for minimizing the glue line. Station 2 applies glue to the edge of the panel and then moves to the 5-roller pressure section. Station 3 is a double motor end trim. Double motor end trim allows for closer part spacing thereby speeding production.Station 4 is a top and bottom rough trim station. Station 5 is top and bottom radius fine trim, and station 6 is double motor corner rounding, station 7 is top and bottom radius scraping, station 8 is top and bottom flat scrapers, station 9 is top and bottom buffing. Machines can also be configured with front and rear mist stations. The result is a finished edge right off the machine with no need for additional processing. Like the rest of the NewCNC line of Edgebanders, the Fuse 9 uses straight forward mechanical design making adjustment simple. Use with PVC, ABS, acrylic, melamine, or wood veneer. Processing speeds up to 75 feet per minute are achievable. Copy wheels can be replaced with multi rolls for edgebanding over hinge cups without gauging.

• High Speed Panel Production
• Touch Screen User Interface
• Pre-Mill
• Glue & Pressure
• Double Motor End Cut
• Top & Bottom Rough Trim
• Top & Bottom Fine Trim
• Double Motor Corner Round
• Radius Scrape
• Flat Scrape
• Top & Bottom Buffers

The NewCNC Fuse 8 M is a heavy-duty Edgebander engineered for continuous duty. This is designed for high quality production with pre-mill and corner rounding. Typical uses would be custom residential & commercial cabinets, closets, and work surfaces. To begin, an anti-stick spray is applied to the top and bottom surface, then Station 1 is a double motor pre-mill section. Pre-mill guarantees a cleanly cut and square edge, even if the panel did not start that way. Next an IR lamp heats the edge for the very best glue penetration and adhesion. Station 2 is motor adjusted and applies glue to the edge of the panel and then moves to the 4-roller pressure section. Station 3 is a double motor end trim. Double motors allow faster feed speeds and allows parts to be ran much closer together equaling greater output. Station 4 is motor adjusted top and bottom flat and/or radius fine trim. Station 5 is double motor corner rounding and switchable from thin to tick tape at the press of a button. Station 6 is motor adjusted top and bottom radius scraping. Station 7 is flat scrapping for a near zero glue line. Just before buffing at station 8 is a spray for buffing compound. The result is a finished edge right off the machine with no need for additional processing. The NewCNC Fuse 8 M uses digital technology to make adjustment simple at the press of a preprogrammed button. Use with PVC, ABS, acrylic, melamine, or wood veneer. Processing speeds up to 59 feet per minute are achievable.

• High Speed Panel Production
• Touch Screen User Interface
• Pre-Mill
• Glue & Pressure
• Double Motor End Cut
• Top & Bottom Trim
• Double Motor Corner Round
• Radius Scrape
• Flat Scrape
• Top & Bottom Buffers

The NewCNC Fuse 8 is a heavy-duty Edgebander engineered for continuous duty. This is designed for high production with pre-mill and corner rounding. Typical uses would be commercial cabinets, closets, and work surfaces. The first station is a double motor pre-mill section. Pre-mill finish cuts the edge and leaves the perfect surface for minimizing the glue line. Station 2 applies glue to the edge of the panel and then moves to the 5-roller pressure section. Station 3 is a double motor end trim. Double motor end trim allows for closer part spacing thereby speeding production. Station 4 is a top and bottom rough trim station. Station 5 is top and bottom radius fine trim, and station 6 is double motor corner rounding, station 7 is top and bottom radius scraping, station 8 is top and bottom buffing. Machines can also be configured with front and rear mist stations. The result is a finished edge right off the machine with no need for additional processing. Like the rest of the NewCNC line of Edgebanders, the Fuse 8 uses straight forward mechanical design making adjustment simple. Use with PVC, ABS, acrylic, melamine, or wood veneer. Processing speeds up to 75 feet per minute are achievable. Copy wheels can be replaced with multi rolls for edgebanding over hinge cups without gauging.

• High Speed Panel Production
• Touch Screen User Interface
• Pre-Mill
• Glue & Pressure
• Double Motor End Cut
• Top & Bottom Rough Trim
• Top & Bottom Fine Trim
• Double Motor Corner Round
• Radius Scrape
• Top & Bottom Buffers

The NewCNC Fuse 7 is a heavy-duty Edgebander designed for a continuous duty cycle. The first station is a double motor pre-mill section. This is especially useful when parts are cut on a beam saw as opposed to a CNC router. Station 2 applies glue to the edge of the panel and then moves to the 4-roller pressure section. Station 3 is a double motor end trim. Double motors allow much faster feed speeds and is more desirable than a single motor end trim machine. It allows parts to be run much closer together. Station 4 is a top and bottom rough trim station. Station 5 is top and bottom radius fine trim, and station 6 is top and bottom scraping, and station 7 is top and bottom buffing. Machines are configured with front spray release agent and rear spray cleaning agent. The result is a finished edge right off the machine with no need for additional processing. Like the rest of the NewCNC line of Edgebanders, the Fuse 7 uses straight forward mechanical design making adjustment simple. Use with PVC, ABS, acrylic, melamine, or wood veneer. Processing speeds up to 75 feet per minute are achievable.

• High Speed Panel Production
• Touch Screen User Interface
• Pre-Mill
• Glue & Pressure
• Double Motor End Cut
• Top & Bottom Rough Trim
• Top & Bottom Fine Trim
• Double Motor Corner Round
• Radius Scrape
• Top & Bottom Buffers

The NewCNC Fuse 6 is a heavy-duty Edgebander designed for a continuous duty cycle. This is not a low-end entry-level machine but does have a very attractive price. The first station applies glue to the edge of the panel and moves into a 4-roller pressure section. Station 2 is a double motor end trim. Double motors allow much faster feed speeds and is more desirable than a single motor end trim machine. Station 3 is a top and bottom rough trim station. Station 4 is top and bottom radius fine trim, station 5 is top and bottom radius scraping, and station 6 and station 6 applies a spray cleaning compound ahead of the top and bottom buffing wheels. The result is a finished edge right off the machine with no need for additional processing. Like the rest of the NewCNC line of Edgebanders, the Fuse 6 uses straight forward mechanical design making adjustment simple. Use with PVC, ABS, acrylic, melamine, or wood veneer. Processing speeds up to 70 feet per minute are achievable. Other machines comparable in price typically run maximum speeds of 21 feet per minute.

• High Speed Panel Production
• Touch Screen User Interface
• Glue & Pressure
• Double Motor End Cut
• Top & Bottom Rough Trim
• Top & Bottom Fine Trim
• Radius Scrape
• Top & Bottom Buffers